Introduction
Most lift installation delays in India start on the drawing board, not on site. A shaft that is 50 mm too narrow, a pit that is 200 mm too shallow, or a slab that blocks the overhead clearance can hold up an installation for weeks. Fixing it means breaking concrete.
This guide explains how elevator shafts are sized, what the standard dimensions look like for common capacities, and which pit, overhead and structural requirements matter most.
What Is an Elevator Shaft
The elevator shaft, also called the hoistway, is the vertical enclosure the car and counterweight travel through. It houses the guide rails, ropes or jacks, landing doors and, in MRL lifts, the machine and controller.
The shaft runs from the bottom of the pit to the underside of the shaft ceiling. Every dimension inside it is set by the lift you choose, not by a general rule. That is the single most important planning point.
The Three Dimensions You Need
An elevator needs three sets of numbers on your drawings, not one.
- Car size: The internal width and depth of the cabin. This sets passenger capacity.
- Shaft size: The clear internal width and depth of the hoistway, measured to the finished wall face.
- Pit and overhead: The depth below the lowest floor and the clear height above the top floor.
A common error is drawing the car size and treating it as the shaft. The shaft must also fit the counterweight, guide rails, door mechanism and running clearances. In a typical passenger lift, the shaft is roughly 500–700 mm wider and 400–600 mm deeper than the car.
Standard Shaft Dimensions by Capacity
The figures below are indicative planning ranges commonly used in India. Final sizes must always come from the manufacturer’s general arrangement (GA) drawing.
Home Lifts
| Capacity | Typical car size (W × D) | Typical shaft size (W × D) |
| 2–3 persons | 800 × 900 mm | 1200 × 1250 mm |
| 4 persons | 900 × 1100 mm | 1400 × 1450 mm |
| 6 persons | 1000 × 1250 mm | 1600 × 1600 mm |
Compact home lifts with side-mounted drives can fit tighter shafts. Ask for the exact layout before finalising.
Passenger Lifts
| Capacity | Typical car size (W × D) | Typical shaft size (W × D) |
| 6 persons (408 kg) | 1100 × 1000 mm | 1650 × 1600 mm |
| 8 persons (544 kg) | 1100 × 1300 mm | 1750 × 1850 mm |
| 10 persons (680 kg) | 1300 × 1400 mm | 1950 × 1950 mm |
| 13 persons (884 kg) | 1600 × 1400 mm | 2200 × 2000 mm |
Hospital and Bed Lifts
Bed lifts need deep cars to carry a patient bed, stretcher and attendants.
- Typical car: 1300–1500 mm wide × 2300–2500 mm deep
- Typical shaft: 2000–2300 mm wide × 2900–3100 mm deep
- Door clear width: usually 1100–1300 mm
Goods Lifts
Goods lift sizes follow the load and the largest item to be carried. A 1000 kg goods lift often uses a car around 1500 × 2000 mm. Capacities in tonnes need larger shafts and heavier structural support.
Pit Depth Requirements
The pit is the space below the lowest landing. It holds buffers, the bottom of the guide rails and safety components.
- Home lifts: often 150–500 mm, depending on the drive
- Passenger traction lifts at 1.0 m/s: commonly 1400–1600 mm
- Higher speeds: deeper pits
The pit must be waterproof. A wet pit damages electrical parts and safety gear. Plan a sump or damp-proof treatment where groundwater is high.
Overhead and Headroom Requirements
Overhead is the clear height from the top floor level to the underside of the shaft ceiling. It provides safe space above the car when it reaches the top.
- Home lifts: often 2600–3200 mm
- Passenger MRL lifts at 1.0 m/s: commonly 3800–4200 mm
- Higher speeds and larger cars: more overhead
Overhead is the most frequently missed dimension. Beams and water tanks above the top floor often eat into it. Check the section drawing, not just the plan.
Machine Room vs MRL Space Needs
A conventional traction lift needs a machine room above the shaft. It is usually larger than the shaft footprint and needs a minimum clear height of about 2000–2200 mm, ventilation and a hook beam.
An MRL lift places the machine and controller inside the shaft. You save the machine room completely. You may still need a small control panel space near the top landing, depending on the design.
Hydraulic lifts need a small pump room, usually near the lowest landing and close to the shaft.
Door Sizes and Landing Requirements
- Standard passenger door clear width: 700–900 mm
- Accessible lifts: at least 900 mm clear opening is commonly recommended
- Bed lifts: 1100 mm or more
- Door height: commonly 2000–2100 mm
Each landing needs a structural opening slightly larger than the door clear size. It also needs space for the push-button box and floor indicator beside the door.
Structural Requirements
Shaft Walls
Shaft walls are usually RCC or brick with RCC bands at regular intervals. The bands give firm fixing points for guide rail brackets. The manufacturer will specify band spacing, often every 1.5 to 2.5 m.
Plumb and Tolerances
The shaft must be vertical within tight limits. A shaft that leans by even 25–30 mm over its height can reduce clearances below the safe minimum. Check plumb at every floor during construction, not after.
Ventilation and Lighting
The shaft needs ventilation openings at the top, as defined by the applicable code and fire safety rules. Permanent lighting inside the shaft helps maintenance teams work safely.
Loads on the Structure
The pit floor and top slab carry reactions from buffers, rails and machines. The manufacturer provides these loads. The structural engineer must design for them.
Codes and Standards
- IS 14665 (Parts 1–5): Electric traction lifts, including installation and safety
- IS 17900: Safety rules for construction and installation of lifts
- National Building Code 2016, Part 8: Lifts in buildings, fire lifts, shaft fire rating
- Harmonised Guidelines for Universal Accessibility in India (2021): Car sizes and controls for wheelchair users
- Gujarat Lifts and Escalators Act and Rules: Licensing before operation
Common Planning Mistakes
- Fixing shaft size before choosing the lift. Different products need different clearances for the same capacity.
- Ignoring the overhead. A beam or tank above the top floor is the usual culprit.
- Shallow pits. Often caused by a raft or plinth level change not accounted for.
- Out-of-plumb walls. Rarely checked floor by floor.
- No space for future upgrades. Hospitals and offices often need bigger cars later.
FAQs
What is the minimum shaft size for a home lift in India?
Compact two-person home lifts can fit shafts around 1200 × 1250 mm. Exact minimums depend on the drive and door type. Always confirm against the manufacturer’s GA drawing.
Can I install a lift without a pit?
Some home lifts and platform lifts work with a very shallow pit or a ramp. Standard passenger traction lifts need a proper pit for buffers and safety gear.
What is the overhead needed for an MRL lift?
Most passenger MRL lifts at 1.0 m/s need roughly 3800–4200 mm. Home MRL lifts usually need less. The final figure depends on car height and speed.
Who gives the final shaft dimensions?
The lift manufacturer gives them through a GA drawing. Architects and structural engineers should work from this drawing.
Can an existing shaft be reused for a new lift?
Often yes. A survey will check width, depth, plumb, pit and overhead. Many modern MRL lifts fit into older shafts with minor civil changes.
Conclusion
Shaft planning comes down to three numbers: shaft size, pit depth and overhead. Get all three from the manufacturer’s drawing before the structure is finalised. Check plumb as the walls rise. Leave margins for future needs, especially in hospitals and commercial buildings.
If your drawings are in progress, send them to a lift engineer for a quick review now.
About Express Elevators
Express Elevators & Infrastructures Pvt. Ltd. has engineered and installed elevators from Rajkot for over 30 years. Our team supports architects and builders with shaft layouts, GA drawings and site surveys for passenger, MRL, hydraulic, hospital, home and capsule lifts.
We design every lift around your building, so installation runs on time and the ride stays smooth.